ARDUINO LCD 1602 (16x2)KEYPAD SHIELD (BLUE LCD) ?>

More in this category

ARDUINO LCD 1602 (16x2)KEYPAD SHIELD (BLUE LCD)

0.0 / 5 0

3910

This is a very popular LCD Keypad shield for Arduino or Freeduino board. It includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Analog Pin 0 is used to read the pushbuttons. The LCD shield supports contrast adjustment and backlit on/off functions. It also expands analog pins for easy analog sensor reading and display.

Introduction

Specification

Operating Voltage:5V
6 Push buttons
Expanded Analog Pinout with standard DFRobot configuration

Documents

Tutorial:

Introduction

The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys â€” select, up, right, down and left. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5 stage voltage divider.

Note: Version 1.1 main updates are the button values, which have being updated on the example code. For older version
check the comments and edit, or use the Enhanced V1.0 library

Diagram

LCD&Keypad Shield

Diagram

Pin Out Diagram

Pin Allocation

Pin	Function
Analog 0	Button (select, up, right, down and left)
Digital 4	DB4
Digital 5	DB5
Digital 6	DB6
Digital 7	DB7
Digital 8	RS (Data or Signal Display Selection)
Digital 9	Enable
Digital 10	Backlit Control

Sample Code

Example use of LiquidCrystal library

//Sample using LiquidCrystal library
#include 
 
/*******************************************************
 
This program will test the LCD panel and the buttons
Mark Bramwell, July 2010
 
********************************************************/
 
// select the pins used on the LCD panel
LiquidCrystal lcd(8, 9, 4, 5, 6, 7);
 
// define some values used by the panel and buttons
int lcd_key     = 0;
int adc_key_in  = 0;
#define btnRIGHT  0
#define btnUP     1
#define btnDOWN   2
#define btnLEFT   3
#define btnSELECT 4
#define btnNONE   5
 
// read the buttons
int read_LCD_buttons()
{
 adc_key_in = analogRead(0);      // read the value from the sensor
 // my buttons when read are centered at these valies: 0, 144, 329, 504, 741
 // we add approx 50 to those values and check to see if we are close
 if (adc_key_in > 1000) return btnNONE; // We make this the 1st option for speed reasons since it will be the most likely result
 // For V1.1 us this threshold
 if (adc_key_in < 50)   return btnRIGHT; 
 if (adc_key_in < 250)  return btnUP;
 if (adc_key_in < 450)  return btnDOWN;
 if (adc_key_in < 650)  return btnLEFT;
 if (adc_key_in < 850)  return btnSELECT; 
 
 // For V1.0 comment the other threshold and use the one below:
/*
 if (adc_key_in < 50)   return btnRIGHT; 
 if (adc_key_in < 195)  return btnUP;
 if (adc_key_in < 380)  return btnDOWN;
 if (adc_key_in < 555)  return btnLEFT;
 if (adc_key_in < 790)  return btnSELECT;  
*/
 
 
 return btnNONE;  // when all others fail, return this...
}
 
void setup()
{
 lcd.begin(16, 2);              // start the library
 lcd.setCursor(0,0);
 lcd.print("Push the buttons"); // print a simple message
}
  
void loop()
{
 lcd.setCursor(9,1);            // move cursor to second line "1" and 9 spaces over
 lcd.print(millis()/1000);      // display seconds elapsed since power-up
 
 
 lcd.setCursor(0,1);            // move to the begining of the second line
 lcd_key = read_LCD_buttons();  // read the buttons
 
 switch (lcd_key)               // depending on which button was pushed, we perform an action
 {
   case btnRIGHT:
     {
     lcd.print("RIGHT ");
     break;
     }
   case btnLEFT:
     {
     lcd.print("LEFT   ");
     break;
     }
   case btnUP: